PAUT-Phased Array Calibration Standard NDT Calibration Blocks

Sort By:  
paut phased array calibration standard block 1018 steel inch version ndt paut calibration block
PAUT-Phased Array Calibration Standard Block 1018 Steel (Inch Version) Geometry:The three radii (.500", 1.000" and 2.000") allow for exit point verification, velocity and sound path calculations. This block contains five holes at 3/64" diameter drilled through the 1.000" width, located at .100", .200", .400", .600", .800", 1.200", 1.400", 1.600", 1.800" and 1.900" from the respective scanning surface.Dimensions: 18.0" x 2.0" x 1.0"
PAUT-Phased Array Calibration Standard Block 1018 Steel (Metric Version) Geometry:The three radii (12.5mm, 25mm and 50mm) allow for exit point verification, velocity and sound path calculations. This metric block contains five holes at 1.2mm diameter drilled through the 25mm width, located at 2.5mm, 5.0mm, 10.0mm, 15.0mm, 20.0mm, 30.0mm, 35.0mm, 45.0mm and 47.5mm from the respective scanning surface. Dimensions: 450mm x 50mm x 25mm
paut phased array calibration standard block 304 stainless steel inch version ndt paut calibration block
PAUT-Phased Array Calibration Standard Block 304 Stainless Steel (Inch Version) Geometry:The three radii (.500", 1.000" and 2.000") allow for exit point verification, velocity and sound path calculations. This block contains five holes at 3/64" diameter drilled through the 1.000" width, located at .100", .200", .400", .600", .800", 1.200", 1.400", 1.600", 1.800" and 1.900" from the respective scanning surface.Dimensions: 18.0" x 2.0" x 1.0"
PAUT-Phased Array Calibration Standard Block 304 Stainless Steel (Metric Version) Geometry:The three radii (12.5mm, 25mm and 50mm) allow for exit point verification, velocity and sound path calculations. This metric block contains five holes at 1.2mm diameter drilled through the 25mm width, located at 2.5mm, 5.0mm, 10.0mm, 15.0mm, 20.0mm, 30.0mm, 35.0mm, 45.0mm and 47.5mm from the respective scanning surface. Dimensions: 450mm x 50mm x 25mm
paut phased array calibration standard block 7075 t6 aluminum inch version ndt paut calibration block
PAUT-Phased Array Calibration Standard Block 7075-T6 Aluminum (Inch Version) Geometry:The three radii (.500", 1.000" and 2.000") allow for exit point verification, velocity and sound path calculations. This block contains five holes at 3/64" diameter drilled through the 1.000" width, located at .100", .200", .400", .600", .800", 1.200", 1.400", 1.600", 1.800" and 1.900" from the respective scanning surface.Dimensions: 18.0" x 2.0" x 1.0"
PAUT-Phased Array Calibration Standard Block 7075-T6 Aluminum (Metric Version) Geometry:The three radii (12.5mm, 25mm and 50mm) allow for exit point verification, velocity and sound path calculations. This metric block contains five holes at 1.2mm diameter drilled through the 25mm width, located at 2.5mm, 5.0mm, 10.0mm, 15.0mm, 20.0mm, 30.0mm, 35.0mm, 45.0mm and 47.5mm from the respective scanning surface. Dimensions: 450mm x 50mm x 25mm
paut phased array calibration standard block 1018 steel inch version ndt paut calibration block
PAUT-Phased Array Calibration Standard Block 1018 Steel (Inch Version) NDT PAUT Calibration Block (7434)

PAUT-Phased Array Calibration Standard Block 1018 Steel (Inch Version)

Geometry:The three radii (.500", 1.000" and 2.000") allow for exit point verification, velocity and sound path calculations. This block contains five holes at 3/64" diameter drilled through the 1.000" width, located at .100", .200", .400", .600", .800", 1.200", 1.400", 1.600", 1.800" and 1.900" from the respective scanning surface.Dimensions: 18.0" x 2.0" x 1.0"
Phased Array Calibration Standard Blocks are used for angle beam verification, probe angle exit points, calibration for wedge delay, sensitivity and DAC/TCG for thicknesses up to 2".
PAUT-Phased Array Calibration Standard Block 1018 Steel (Inch Version) Geometry:The three radii (.500", 1.000" and 2.000") allow for exit point verification, velocity and sound path calculations. This block contains five holes at 3/64" diameter drilled through the 1.000" width, located at .100", .200", .400", .600", .800", 1.200", 1.400", 1.600", 1.800" and 1.900" from the respective scanning surface.Dimensions: 18.0" x 2.0" x 1.0"
PAUT-Phased Array Calibration Standard Block 1018 Steel (Metric Version) NDT PAUT Calibration Block (7435)
PAUT-Phased Array Calibration Standard Block 1018 Steel (Metric Version) Geometry:The three radii (12.5mm, 25mm and 50mm) allow for exit point verification, velocity and sound path calculations. This metric block contains five holes at 1.2mm diameter drilled through the 25mm width, located at 2.5mm, 5.0mm, 10.0mm, 15.0mm, 20.0mm, 30.0mm, 35.0mm, 45.0mm and 47.5mm from the respective scanning surface. Dimensions: 450mm x 50mm x 25mm Phased Array Calibration Standard Blocks are used for angle beam verification, probe angle exit points, calibration for wedge delay, sensitivity and DAC/TCG for thicknesses up to 2".
PAUT-Phased Array Calibration Standard Block 1018 Steel (Metric Version) Geometry:The three radii (12.5mm, 25mm and 50mm) allow for exit point verification, velocity and sound path calculations. This metric block contains five holes at 1.2mm diameter drilled through the 25mm width, located at 2.5mm, 5.0mm, 10.0mm, 15.0mm, 20.0mm, 30.0mm, 35.0mm, 45.0mm and 47.5mm from the respective scanning surface. Dimensions: 450mm x 50mm x 25mm
paut phased array calibration standard block 304 stainless steel inch version ndt paut calibration block
PAUT-Phased Array Calibration Standard Block 304 Stainless Steel (Inch Version) NDT PAUT Calibration Block (7436)

PAUT-Phased Array Calibration Standard Block 304 Stainless Steel (Inch Version)

Geometry:The three radii (.500", 1.000" and 2.000") allow for exit point verification, velocity and sound path calculations. This block contains five holes at 3/64" diameter drilled through the 1.000" width, located at .100", .200", .400", .600", .800", 1.200", 1.400", 1.600", 1.800" and 1.900" from the respective scanning surface.Dimensions: 18.0" x 2.0" x 1.0"
Phased Array Calibration Standard Blocks are used for angle beam verification, probe angle exit points, calibration for wedge delay, sensitivity and DAC/TCG for thicknesses up to 2".
PAUT-Phased Array Calibration Standard Block 304 Stainless Steel (Inch Version) Geometry:The three radii (.500", 1.000" and 2.000") allow for exit point verification, velocity and sound path calculations. This block contains five holes at 3/64" diameter drilled through the 1.000" width, located at .100", .200", .400", .600", .800", 1.200", 1.400", 1.600", 1.800" and 1.900" from the respective scanning surface.Dimensions: 18.0" x 2.0" x 1.0"
PAUT-Phased Array Calibration Standard Block 304 Stainless Steel (Metric Version) NDT PAUT Calibration Block (7437)
PAUT-Phased Array Calibration Standard Block 304 Stainless Steel (Metric Version) Geometry:The three radii (12.5mm, 25mm and 50mm) allow for exit point verification, velocity and sound path calculations. This metric block contains five holes at 1.2mm diameter drilled through the 25mm width, located at 2.5mm, 5.0mm, 10.0mm, 15.0mm, 20.0mm, 30.0mm, 35.0mm, 45.0mm and 47.5mm from the respective scanning surface. Dimensions: 450mm x 50mm x 25mm Phased Array Calibration Standard Blocks are used for angle beam verification, probe angle exit points, calibration for wedge delay, sensitivity and DAC/TCG for thicknesses up to 2".
PAUT-Phased Array Calibration Standard Block 304 Stainless Steel (Metric Version) Geometry:The three radii (12.5mm, 25mm and 50mm) allow for exit point verification, velocity and sound path calculations. This metric block contains five holes at 1.2mm diameter drilled through the 25mm width, located at 2.5mm, 5.0mm, 10.0mm, 15.0mm, 20.0mm, 30.0mm, 35.0mm, 45.0mm and 47.5mm from the respective scanning surface. Dimensions: 450mm x 50mm x 25mm
paut phased array calibration standard block 7075 t6 aluminum inch version ndt paut calibration block
PAUT-Phased Array Calibration Standard Block 7075-T6 Aluminum (Inch Version) NDT PAUT Calibration Block (7438)

PAUT-Phased Array Calibration Standard Block 7075-T6 Aluminum (Inch Version)

Geometry:The three radii (.500", 1.000" and 2.000") allow for exit point verification, velocity and sound path calculations. This block contains five holes at 3/64" diameter drilled through the 1.000" width, located at .100", .200", .400", .600", .800", 1.200", 1.400", 1.600", 1.800" and 1.900" from the respective scanning surface.Dimensions: 18.0" x 2.0" x 1.0"
Phased Array Calibration Standard Blocks are used for angle beam verification, probe angle exit points, calibration for wedge delay, sensitivity and DAC/TCG for thicknesses up to 2".
PAUT-Phased Array Calibration Standard Block 7075-T6 Aluminum (Inch Version) Geometry:The three radii (.500", 1.000" and 2.000") allow for exit point verification, velocity and sound path calculations. This block contains five holes at 3/64" diameter drilled through the 1.000" width, located at .100", .200", .400", .600", .800", 1.200", 1.400", 1.600", 1.800" and 1.900" from the respective scanning surface.Dimensions: 18.0" x 2.0" x 1.0"
PAUT-Phased Array Calibration Standard Block 7075-T6 Aluminum (Metric Version) NDT PAUT Calibration Block (7439)
PAUT-Phased Array Calibration Standard Block 7075-T6 Aluminum (Metric Version) Geometry:The three radii (12.5mm, 25mm and 50mm) allow for exit point verification, velocity and sound path calculations. This metric block contains five holes at 1.2mm diameter drilled through the 25mm width, located at 2.5mm, 5.0mm, 10.0mm, 15.0mm, 20.0mm, 30.0mm, 35.0mm, 45.0mm and 47.5mm from the respective scanning surface. Dimensions: 450mm x 50mm x 25mm Phased Array Calibration Standard Blocks are used for angle beam verification, probe angle exit points, calibration for wedge delay, sensitivity and DAC/TCG for thicknesses up to 2".
PAUT-Phased Array Calibration Standard Block 7075-T6 Aluminum (Metric Version) Geometry:The three radii (12.5mm, 25mm and 50mm) allow for exit point verification, velocity and sound path calculations. This metric block contains five holes at 1.2mm diameter drilled through the 25mm width, located at 2.5mm, 5.0mm, 10.0mm, 15.0mm, 20.0mm, 30.0mm, 35.0mm, 45.0mm and 47.5mm from the respective scanning surface. Dimensions: 450mm x 50mm x 25mm
Per Page      1 - 6 of 6
  • 1