CUSTOM CALIBRATION BLOCKS

NDE offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our CUSTOM CALIBRATION BLOCKS, please contact us at +91-9043-660-755 or send an email to info@ndeflawtechnologies.com.and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
Sort By:  
PAUT These pipe calibration blocks are specially designed to facilitate phased array UT (PAUT). The NDE block design includes various modifications to the original ASME design, including extra axial and arc length, a rearranged notch layout and a 10° angled cut on one end for blocks over 5" NPS. These modifications help to minimize unwanted "noise" from the backwall while performing DAC/TCG calibrations with phased array UT equipment. A calibration block should be a section of pipe of the same nominal size, schedule, heat treatment and material specifications as the material being examined. we maintains a large inventory of raw material for the machining of these standards and they can be made from customer supplied material as well. The Phased Array Pipe Calibration Block contains 4 EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" maximum width (most notches are approximately .030" - .040" wide) x 1.000" minimum length. Blocks 5" NPS and smaller are left at 360°, while blocks over 5" are milled to a 180°/120°/90°/60° arc section (depending on nominal pipe size). All blocks are 12" in axial length minimum or 10T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-43.3, with PAUT modification for PAUT.
PAUT TOFD Validation/Calibration Blocks. NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
PAUT TOFD Validation/Calibration Blocks. NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
paut asme type pipe calibration block ndt paut calibration block
ASME Angle Beam Calibration Block For Pipe. Ready to request a quote for some blocks? Here's what we need... What is the pipe material? What is the pipe NPS / OD size? What is the pipe schedule / wall thickness? Is NDE supplying the material or will it be customer supplied? Are there any changes or modifications requested to the ASME block design?
paut asme type pipe calibration block ndt paut calibration block
ASME Angle Beam Calibration Block For Pipe. Ready to request a quote for some blocks? Here's what we need... What is the pipe material? What is the pipe NPS / OD size? What is the pipe schedule / wall thickness? Is NDE supplying the material or will it be customer supplied? Are there any changes or modifications requested to the ASME block design?
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
astm distance amplitude set 19 4340 steel ndt calibration block
ASTM Single Custom Blocks Ready to request a quote for some blocks? Here's what we need... What is the material? What is the FBH diameter? What is the metal travel distance? What is the block diameter/shape? Is NDE supplying the material or will it be customer supplied? Are there any changes or modifications requested to the ASTM block design?
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
PAUT Validation/Demonstration Blocks. DISSIMILAR WELD SAMPLES WITH DEFECT FOR NUCLEAR POWER PLANTS. NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
NDT Reference Standards for Bearing Industry. NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at +91-9043-660-755 or send an email to info@ndeflawtechnologies.com.and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
PAUT TOFD Validation/Calibration Blocks. NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
paut asme type pipe calibration block ndt paut calibration block
Ready to request a quote for some blocks? Here's what we need... What is the pipe material? What is the pipe NPS / OD size? What is the pipe schedule / wall thickness? Is NDE TECH supplying the material or will it be customer supplied? Are there any changes or modifications requested to the our block design? Call our office or drop us an e-mail with the above information.
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
Standard NDT Boiler Tubes Flawed Specimens Kit. For NDT Demonstration. contains 10 Carbon steel pipes, 50mm OD diameter x 5mm WT with range of defects listed in the BS code for boiler tube inspection. 25 total Flaws. Documentation: NDT Verification Reports,C of C, CAD Drawings and Test Sheets. Material: Carbon Steel
AUTO UT Validation/Demonstration Blocks
NDE offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at +91-9043-660-755 or send an email to info@ndeflawtechnologies.com.and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
Validation/Demonstration Blocks
PAUT Pipeing Calibration Blocks.
PAUT These pipe calibration blocks are specially designed to facilitate phased array UT (PAUT). The NDE block design includes various modifications to the original ASME design, including extra axial and arc length, a rearranged notch layout and a 10° angled cut on one end for blocks over 5" NPS. These modifications help to minimize unwanted "noise" from the backwall while performing DAC/TCG calibrations with phased array UT equipment. A calibration block should be a section of pipe of the same nominal size, schedule, heat treatment and material specifications as the material being examined. we maintains a large inventory of raw material for the machining of these standards and they can be made from customer supplied material as well. The Phased Array Pipe Calibration Block contains 4 EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" maximum width (most notches are approximately .030" - .040" wide) x 1.000" minimum length. Blocks 5" NPS and smaller are left at 360°, while blocks over 5" are milled to a 180°/120°/90°/60° arc section (depending on nominal pipe size). All blocks are 12" in axial length minimum or 10T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-43.3, with PAUT modification for PAUT.
PAUT These pipe calibration blocks are specially designed to facilitate phased array UT (PAUT). The NDE block design includes various modifications to the original ASME design, including extra axial and arc length, a rearranged notch layout and a 10° angled cut on one end for blocks over 5" NPS. These modifications help to minimize unwanted "noise" from the backwall while performing DAC/TCG calibrations with phased array UT equipment. A calibration block should be a section of pipe of the same nominal size, schedule, heat treatment and material specifications as the material being examined. we maintains a large inventory of raw material for the machining of these standards and they can be made from customer supplied material as well. The Phased Array Pipe Calibration Block contains 4 EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" maximum width (most notches are approximately .030" - .040" wide) x 1.000" minimum length. Blocks 5" NPS and smaller are left at 360°, while blocks over 5" are milled to a 180°/120°/90°/60° arc section (depending on nominal pipe size). All blocks are 12" in axial length minimum or 10T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-43.3, with PAUT modification for PAUT.
PAUT TOFD Validation/Calibration Blocks.
PAUT TOFD Validation/Calibration Blocks. NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
PAUT TOFD Validation/Calibration Blocks. NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
PAUT TOFD Validation/Calibration Blocks.
PAUT TOFD Validation/Calibration Blocks. NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
PAUT TOFD Validation/Calibration Blocks. NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
Angle Beam Calibration Blocks ( ASME )
PAUT These pipe calibration blocks are specially designed to facilitate phased array UT (PAUT). The NDE block design includes various modifications to the original ASME design, including extra axial and arc length, a rearranged notch layout and a 10° angled cut on one end for blocks over 5" NPS. These modifications help to minimize unwanted "noise" from the backwall while performing DAC/TCG calibrations with phased array UT equipment. A calibration block should be a section of pipe of the same nominal size, schedule, heat treatment and material specifications as the material being examined. we maintains a large inventory of raw material for the machining of these standards and they can be made from customer supplied material as well. The Phased Array Pipe Calibration Block contains 4 EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" maximum width (most notches are approximately .030" - .040" wide) x 1.000" minimum length. Blocks 5" NPS and smaller are left at 360°, while blocks over 5" are milled to a 180°/120°/90°/60° arc section (depending on nominal pipe size). All blocks are 12" in axial length minimum or 10T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-43.3, with PAUT modification for PAUT.
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
Angle Beam Calibration Blocks As Per ASME Section V Article 4 Figure T-434.3.
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
paut asme type pipe calibration block ndt paut calibration block
ASME Angle Beam Calibration Block (7079)

ASME Angle Beam Calibration Block For Pipe


Ready to request a quote for some blocks? Here's what we need...
What is the pipe material?
What is the pipe NPS / OD size?
What is the pipe schedule / wall thickness?
Is NDE supplying the material or will it be customer supplied?
Are there any changes or modifications requested to the ASME block design?

ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3. In small quantities, blocks can be shipped in approximately 1 week, with rush options always available. Larger quantities will take longer, however we're happy to do partial shipments.
ASME Angle Beam Calibration Block For Pipe. Ready to request a quote for some blocks? Here's what we need... What is the pipe material? What is the pipe NPS / OD size? What is the pipe schedule / wall thickness? Is NDE supplying the material or will it be customer supplied? Are there any changes or modifications requested to the ASME block design?
paut asme type pipe calibration block ndt paut calibration block
ASME Angle Beam Calibration Block For Pipe (7079)

ASME Angle Beam Calibration Block For Pipe


Ready to request a quote for some blocks? Here's what we need...
What is the pipe material?
What is the pipe NPS / OD size?
What is the pipe schedule / wall thickness?
Is NDE supplying the material or will it be customer supplied?
Are there any changes or modifications requested to the ASME block design?

ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3. In small quantities, blocks can be shipped in approximately 1 week, with rush options always available. Larger quantities will take longer, however we're happy to do partial shipments.
ASME Angle Beam Calibration Block For Pipe. Ready to request a quote for some blocks? Here's what we need... What is the pipe material? What is the pipe NPS / OD size? What is the pipe schedule / wall thickness? Is NDE supplying the material or will it be customer supplied? Are there any changes or modifications requested to the ASME block design?
ASME Angle Beam Calibration Blocks
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3. FOR PAUT These pipe calibration blocks are specially designed to facilitate phased array UT (PAUT). The NDE block design includes various modifications to the original ASME design, including extra axial and arc length, a rearranged notch layout and a 10° angled cut on one end for blocks over 5" NPS. These modifications help to minimize unwanted "noise" from the backwall while performing DAC/TCG calibrations with phased array UT equipment. A calibration block should be a section of pipe of the same nominal size, schedule, heat treatment and material specifications as the material being examined. we maintains a large inventory of raw material for the machining of these standards and they can be made from customer supplied material as well. The Phased Array Pipe Calibration Block contains 4 EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" maximum width (most notches are approximately .030" - .040" wide) x 1.000" minimum length. Blocks 5" NPS and smaller are left at 360°, while blocks over 5" are milled to a 180°/120°/90°/60° arc section (depending on nominal pipe size). All blocks are 12" in axial length minimum or 10T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-43.3, with PAUT modification for PAUT.
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
ASME Angle Beam Calibration Blocks
FOR PAUT These pipe calibration blocks are specially designed to facilitate phased array UT (PAUT). The NDE block design includes various modifications to the original ASME design, including extra axial and arc length, a rearranged notch layout and a 10° angled cut on one end for blocks over 5" NPS. These modifications help to minimize unwanted "noise" from the backwall while performing DAC/TCG calibrations with phased array UT equipment. A calibration block should be a section of pipe of the same nominal size, schedule, heat treatment and material specifications as the material being examined. we maintains a large inventory of raw material for the machining of these standards and they can be made from customer supplied material as well. The Phased Array Pipe Calibration Block contains 4 EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" maximum width (most notches are approximately .030" - .040" wide) x 1.000" minimum length. Blocks 5" NPS and smaller are left at 360°, while blocks over 5" are milled to a 180°/120°/90°/60° arc section (depending on nominal pipe size). All blocks are 12" in axial length minimum or 10T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-43.3, with PAUT modification for PAUT.
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
ASME Section V Article 4 Figure T-434.3. Calibration Blocks
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
astm distance amplitude set 19 4340 steel ndt calibration block
ASTM Single Custom Blocks (7090)

ASTM Single Custom Blocks

Ready to request a quote for some blocks? Here's what we need...
What is the material?
What is the FBH diameter?
What is the metal travel distance?
What is the block diameter/shape?
Is NDE supplying the material or will it be customer supplied?
Are there any changes or modifications requested to the ASTM block design?

blocks are available in exotic alloys, extra small or large diameter FBHs shapes other than the standard 2" diameter round, metric dimensions, concave or convex radius ends, or non-typical quantities of blocks per set. Extra-long blocks up to 40" metal travel distance at 4" diameter are also available.

Flat-bottom hole diameter: 1/64" to 16/64"
Metal Travel Distance: .050" to 40.000".
Material: Most alloys including exotics. Special colored anodizing is available for aluminum blocks.
Used for measurement of the sensitivity and/or resolution of normal beam transducers. In accordance with ASTM E127 (aluminum alloys) or E428 (all other alloys).
ASTM Single Custom Blocks Ready to request a quote for some blocks? Here's what we need... What is the material? What is the FBH diameter? What is the metal travel distance? What is the block diameter/shape? Is NDE supplying the material or will it be customer supplied? Are there any changes or modifications requested to the ASTM block design?
Calibration Blocks For ASME Section V Article 4 Figure T-434.3.
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
Cladding Weld Overlay NDT CALIBRATION BLOCKS
NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
CUSTOM NDT FBH CALIBRATION BLOCKS
NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
Customized TKY NDT FLAWED SPECIMENS
NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
DISSIMILAR WELD SAMPLES WITH DEFECT FOR NUCLEAR POWER PLANTS.
PAUT Validation/Demonstration Blocks. DISSIMILAR WELD SAMPLES WITH DEFECT FOR NUCLEAR POWER PLANTS. NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
PAUT Validation/Demonstration Blocks. DISSIMILAR WELD SAMPLES WITH DEFECT FOR NUCLEAR POWER PLANTS. NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
NDT Reference Standards for Bearing Industry.
NDT Reference Standards for Bearing Industry. NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at +91-9043-660-755 or send an email to info@ndeflawtechnologies.com.and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
NDT Reference Standards for Bearing Industry. NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at +91-9043-660-755 or send an email to info@ndeflawtechnologies.com.and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
PAUT TOFD Validation Calibration Blocks.
PAUT TOFD Validation Calibration Blocks. NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
PAUT TOFD Validation/Calibration Blocks.
PAUT TOFD Validation/Calibration Blocks. PAUT TOFD Validation/Calibration Blocks. NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
PAUT TOFD Validation/Calibration Blocks. NDE TECH offers calibration blocks and flawed specimens. Please browse our products to find the best one for you. If you have any questions about NDE and our NDT Standard Calibration Blocks, please contact us at + 91-9043-660-755 or send an email to info@ndeflawtechnologies.com hashtag#welding hashtag#calibration hashtag#demonstration and to know more details about block and specimens log on to www.ndtproduct.com Our knowledgeable customer service staff is happy to assist you.
paut asme type pipe calibration block ndt paut calibration block
PAUT- ASME Type Pipe Calibration Block NDT PAUT Calibration Block (7424)
These pipe calibration blocks are specially designed to facilitate phased array UT (PAUT). The NDE block design includes various modifications to the original ASME design, including extra axial and arc length, a rearranged notch layout and a 10° angled cut on one end for blocks over 5" NPS. These modifications help to minimize unwanted "noise" from the backwall while performing DAC/TCG calibrations with phased array UT equipment. A calibration block should be a section of pipe of the same nominal size, schedule, heat treatment and material specifications as the material being examined. we maintains a large inventory of raw material for the machining of these standards and they can be made from customer supplied material as well. The Phased Array Pipe Calibration Block contains 4 EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" maximum width (most notches are approximately .030" - .040" wide) x 1.000" minimum length. Blocks 5" NPS and smaller are left at 360°, while blocks over 5" are milled to a 180°/120°/90°/60° arc section (depending on nominal pipe size). All blocks are 12" in axial length minimum or 10T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-43.3, with PAUT modification for PAUT.
Ready to request a quote for some blocks? Here's what we need... What is the pipe material? What is the pipe NPS / OD size? What is the pipe schedule / wall thickness? Is NDE TECH supplying the material or will it be customer supplied? Are there any changes or modifications requested to the our block design? Call our office or drop us an e-mail with the above information.
Pipe EDM notches Calibration Blocks As Per ASME Section V
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
Piping Calibration Blocks
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
ASME Angle Beam Calibration Blocks contain (4) EDM notches (axial and circumferential on both OD and ID) at a depth of 8-11% of nominal wall thickness x 1/4" max wide (most notches are approximately .020-.030" wide) x 1.000" min long. Blocks 4" NPS and smaller are left at 360°, while blocks over 4" are milled to an 8" arc section. All blocks are 8" in axial length, or 8T, whichever is greater. Made in accordance with ASME Section V Article 4 Figure T-434.3.
Standard Boiler Tubes Kit As Per BS code
Standard NDT Boiler Tubes Flawed Specimens Kit. For NDT Demonstration. contains 10 Carbon steel pipes, 50mm OD diameter x 5mm WT with range of defects listed in the BS code for boiler tube inspection. 25 total Flaws. Documentation: NDT Verification Reports,C of C, CAD Drawings and Test Sheets. Material: Carbon Steel
Standard NDT Boiler Tubes Flawed Specimens Kit. For NDT Demonstration. contains 10 Carbon steel pipes, 50mm OD diameter x 5mm WT with range of defects listed in the BS code for boiler tube inspection. 25 total Flaws. Documentation: NDT Verification Reports,C of C, CAD Drawings and Test Sheets. Material: Carbon Steel
Per Page      1 - 24 of 24
  • 1